- 097-Answer to Steve Bruno's Half A Fubar Size Question
- 001_Tandy's Next Speed 400 Project
- 002_Making Wing Ribs
- 003_Received Four Orders
- 004_Fuselage Scaled Drawing
- 005_Fuselage Sides (Part 1)
- 006_Fuselage Sides (Part 2)
- 007_Fuselage Sides (Part 3)
- 008_Joining the Fuselage Sides (Part 1)
- 009_Joining the Fuselage Sides (Part 2)
- 010_Revised Cowl Drawing
- 011_Framing the Vertical Tail (Part 1)
- 012_Framing the Vertical Tail (Part 2)
- 013_Framing the Horizontal Tail (Part 1)
- 014_Framing the Horizontal Tail (Part 2)
- 015_Framing the Horizontal Tail (Part 3)
- 016_Framing the Horizontal Tail (Part 4)
- 017_Framing the Horizontal Tail (Part 5)
- 018_Horizontal Tail Attachment Blocks
- 019_Fin-Stab-Fuselage Interface
- 020_Fuselage Stab Saddle
- 021_Framing Stab Tip Panels (Part 1)
- 022_Framing Stab Tip Panels (Part 2)
- 023_Installing the Fin
- 024_Incorporating the Rudder
- 025_Firewall and Landing Gear
- 026_Firewall Lamination and Installation
- 027_Pylon Construction (1)
- 028_Pylon Construction (2)
- 029_Servo Installation
- 030_Making Removable Push Rod Ends
- 031_Elevator Push Rod Installation
- 032_Rudder Push Rod Installation
- 033_Finishing Push Rod Exits
- 034_Wing Construction (Part 1)
- 035_Wing Construction (Part 2)
- 036_Wing Construction (Part 3)
- 037_First Weight Estimate
- 038_Wing Construction (Part 4)
- 039_Wing Construction (Part 5)
- 040_Wing Construction (Part 6)
- 041_Wing Construction (Part 7)
- 042_Wing Construction (Part 8)
- 043_Wing Construction (Part 9)
- 044_Wing Construction (Part 10)
- 045_Wing Construction (Part 11)
- 046_Wing Construction (Part 12)
- 047_Fuselage Wing Saddle
- 048_Tail Skid
- 049_Wing Interface with Wing Saddle
- 050_Second Weight Estimate
- 051_Receiver Location and Installation
- 052_Speed Control Switch Installation
- 053_Receiver Hatch Cover (Part 1)
- 054_Receiver Hatch Cover (Part 2)
- 055_Receiver Hatch Cover (Part 3)
- 056_Fuselage Rear Planking & Dorsal Fin
- 057_Servo Hatch Cover
- 058_Pylon Installation and Third Weight and Balance Check
- 059_Electronic Speed Controller (ESC) Installation
- 060_LiPo Battery Hatch-Mount
- 061_Completing Fuselage Planking
- 062_Cowl Design (Part 1)
- 063_Cowl Design (Part 2)
- 064_Pylon Fuselage Fillet
- 065_Pylon Wing Saddle Fillet
- 066_Stab Covering Fix
- 067_Structural Component Weights
- 068_Uncovered RTF Weight
- 069_Silking the Fuselage Part 1
- 070_Silking the Fuselage Part 2
- 071_Silking the Fuselage Part 3
- 072_Silking the Fuselage (Part 4)
- 073_Silking the Fuselage (Part 5)
- 074_Red Dye in Clear Dope
- 075_Decal Order
- 076_Holding Fixtures for Spray Painting
- 077_Covering the Stab
- 078_Covering the Elevators
- 079_Spraying Klass Kote
- 080_Covering the Wing (Part 1)
- 081_Covering the Wing (Part 2)
- 082_Covering Weights
- 083_Stab Skid Protection
- 084_Elevator Hinge Pin Procedure
- 085_Installing Wing Keys
- 086_Final Assembly (Part 1)
- 087_Final Assembly (Part 2)
- 088_Required Ballast Weight Equation
- 089_Repositioning the Speed 400 Motor Forward
- 090_Callie Graphics Decals
- 091_Final Balance
- 092_Pre-Flight Balance
- 093_Maiden Flight
- 094_Preparations for 2nd Test Flights
- 095_Wheel Modification
- 096_Second Series of Test Flights
