- 001 Winter Project-2
- 002 Revised Scaling for SAM LMR
- 003 Original Lancer 72 Plan
- 004 Thrust Line
- 005 Equipment Orders
- 006 Received First Order
- 007 Redesign of Wing Structure
- 008 Received Second Order
- 009 Printed Wing Plans
- 010 Wing Leading Edges
- 011 Received Third Order Today
- 012 2nd Wood Order and Cutting Out Wing Rib Patterns
- 013 Straightening Bowed Leading Edges
- 014 Cutting Out Wing Ribs
- 015 Received Fourth Order
- 016 Locating the Firewall Position
- 017 Final iteration on the Wing Structure
- 018 Wing Rib Fabrication Status (Part 1)
- 019 Wing Rib Fabrication Status (Part 2)
- 020 Making Wing Tips (Part 1)
- 021 Making Wing Tips (Part 2)
- 022 Making Wing Tips (Part 3)
- 023 Change in Wing Spar Wood
- 024 Framing Wing's Right Panel
- 025a
Wing's Root Rib
Jig (Correction)
- 026 Ribs in Right wing Panel
- 027 Installation of Top Main Spar
- 028 Installation of Top Rear Spar
- 029 Installation of Bottom Rear Spar
- 030 Trailing Edge Gussets
- 031 Straight Trailing Edge
- 032 Contouring Right Wing Tip
- 033 Right Wing Tip Top Planking
- 034 Right Wing Diagonals
- 035 Right Wing Shear Webs
- 036 Right Wing Tip Bottom Planking
- 037 Leading Edge Planking Concerns
- 038 Left Wing Panel (Brief Status-1)
- 039 Left Wing Panel (Brief Status-2)
- 040 Left Wing Panel (Brief Status-3)
- 041 Left Wing Panel (Brief Status-4)
- 042 Cutting out the Wing's Leading Edge Planking
- 043 Jig Approach for Joining Wing Panels (Part 1)
- 044 Jig Approach for Joining Wing Panels (Part 2)
- 045 Jig Approach for Joining Wing Panels (Part 3)
- 046 Dihedral Bracing (Part 1)
- 047 Dihedral Bracing (Part 2)
- 048 Dihedral Bracing (Part 3)
- 049 Installation of the Permanent No.1V Ribs
- 050 Installation of Remaining Wing Ribs(1)
- 051 Wing Rear Attachment
- 052 Glue
- 053 Main Spar Shear Webs
- 054 Top Right Leading Edge Planking (Part 1)
- 055 Top Right Leading Edge Planking (Part 2)
- 056 Bottom Right Leading Edge Planking (Part 3)
- 057 Right Wing Panel Evaluation
- 058 Bottom Left Leading Edge Planking (Part 4)
- 059 Top Left Leading Edge Planking (Part 5)
- 060 Specification Review for the Lancer 850 Project
- 061 Planking the Center Section (Part 1)
- 062 Planking the Center Section (Part 2)
- 063 Planking the Center Section (Part 3)
- 064 Shaping the Wing's Leading Edge
- 065 Fuselage Longeron Selection
- 066 Revised Cowl and Tail Mount
- 067 Splicing Fuselage Longeron
- 068 Wing Attachment Concern
- 069 Sizing the Elevator and Framing Fuselage Sides
- 070 Fuselage Side Framing Complete
- 071 Top Longeron Spruce Doublers
- 072 Joining the Two Sides (Part 1)
- 073 Joining the Two Sides (Part 2)
- 074 Joining the Two Sides (Part 3)
- 075 Joining the Two Sides (Part 4)
- 076 Joining the Two Sides (Part 5)
- 077 Bulkhead C and Front Wing Attachment
- 078 Planking Shelf and Bulkhead C Installation
- 079 Wing Rear Attachment
- 080 Evaluation of Wing Alignment
- 081 Completing Rear Wing Attachment
- 082 Driver for Nylon Screws)
- 083 Horizontal Tail Construction (Part 1)
- 084 Horizontal Tail Construction (Part 2)
- 085 Wing Bolt Change
- 086 Horizontal Tail Construction (Part 3)
- 087 Horizontal Tail Construction (Part 4)
- 088 Horizontal Tail Construction (Part 5)
- 089 Fuselage Bulkhead Drawings Arrival
- 090 Horizontal Tail Construction (Part 6)
- 091 Horizontal Tail Construction (Part 7)
- 092 Design of the Fuselage's Stab Mounting Structure (Part 1)
- 093 Design of the Fuselage's Stab Mounting Structure (Part 2)
- 094 Design of the Fuselage's Stab Mounting Structure (Part 3)
- 095 Design of the Fuselage's Stab Mounting Structure (Part 4)
- 096 Design of the Fuselage's Stab Mounting Structure (Part 5)
- 097 Design of the Fuselage's Stab Mounting Structure (Part 6)
- 098 Removable Stab Fuselage Attachment (Part 1)
- 099 Removable Stab Fuselage Attachment (Part 2)
- 100 Removable Stab Fuselage Attachment (Part 3)
- 101 Elevator Construction
- 102 Hinging Elevator to Stab
- 103 Completing the Horizontal Tail
- 104 Vertical Tail Construction (Part 1)
- 105 Vertical Tail Construction (Part 2)
- 106 Vertical Tail Construction (Part 3)
- 107 Hinging the Rudder and Reworking The Tail Post (Part 1)
- 108 Reworking The Tail Post (Part 2)
- 109 Vertical Tail Construction (Part 4)
- 110 Vertical Tail Construction (Part 5)
- 111 Servo Rails and Installations
- 112 Elevator Push Rod Installation
- 113 Rudder Push Rod Routing
- 114 Rudder Push Rod Installation
- 115 Rudder Push Rod Installation (Part 2)
- 116 Receiver Installation
- 117 Firewall Pattern
- 118 Making the Firewall
- 119 First Weight and Balance
- 120 Strips for Fuselage Standoffs
- 121 Installing Bulkheads P and Q
- 122 Bulkheads D, E, F, and H (Part 1)
- 123 Stringer Modification
- 124 Bulkheads (Part 2)
- 125 Bulkhead Grouping (Part 1)
- 125 Bulkheads (Part 3)
- 126 Landing Gear Design Modification
- 127 Original Landing Gear
- 127b Revision to Report No. 127 Forthcoming
- 128 Bending Landing Gear Front Strut
- 129 Bending Landing Gear Rear Strut
- 130 Received Fifth Order
- 131 Landing Gear Strut Joints
- 132 Landing Gear Mounting Pad
- 133 Installing Rx Battery Pack and Firewall
- 134 Received Sixth Order
- 135 LiPo Battery Pack Track and Adjustable Slide (Part 1)
- 136 LiPo Battery Pack Track and Adjustable Slide (Part 2)
- 137 Installing Electronic Speed Control
- 138 Fuselage Side Stringer
- 139 Installation of Futaba Receiver Switch
- 140 Revision To Landing Gear installation (Part 1)
- 141 Revision To Landing Gear installation (Part 2)
- 142 Removable LG Section
- 143 Elevator Push Rod Exit and Right Side Stringer
- 144 Completing Elevator Push Rod Exit
- 145 Received sixth Order
- 146 Resolving Bowed Bottom Longeron Problem (Part 1)
- 147 Rudder Push Rod Exit
- 148 Wire Landing Gear Indexing
- 149 Resolving Bowed Bottom Longeron Problem (Part 2)
- 150 Lining the Landing Gear Section
- 151 Resolving Bowed Bottom Longeron Problem (Part 3)
- 152 Finishing Bottom Bulkheads
- 153 Finishing Bottom Stringers
- 154 Tail Wheel Design and Installation (Part 1)
- 155 Tail Wheel Design and Installation (Part 2)
- 156 Matching the Rudder Contour
- 157 Second Weight and Balance
- 158 Integration of Tail Assembly with Turtle Deck
- 159 Performance Prediction Comparisons
- 160 Cowl Design (Part 1)
- 161 Cowl Design (Part 2)
- 162 Cowl Design (Part 3)
- 163 Cowl Design (Part 4)
- 164 Cowl Design (Part 5)
- 165 Cowl Design (Part 6)
- 166 Cowl Design (Part 7)
- 167 Cowl Design (Part 8)
- 168 Cowl Design (Part 9)
- 169 Cowl Design (Part 10)
- 170 Cowl Design (Part 11) Revision A
- 170 Cowl Design (Part 11)
- 171 Barrel Planking
- 172 Cowl Design (Part 12)
- 173 Cowl Design (Part 13) - Completion
- 174 Plastic Grommet for Wall Hanging
- 175 Test Setup for Wing Insertion
- 176 Making the Instrument Panel
- 177 Bulkhead-Stringer Structure Behind Wing Fairing
- 178 Building Bulkhead-Stringer Structure Behind Wing Fairing
- 179 Fuselage Fairing over the Wing (Part 1)
- 180 Fuselage Fairing over the Wing (Part 2)
- 181 Fuselage Fairing over the Wing (Part 3)
- 182 Fuselage Fairing over the Wing (Part 4)
- 183 Fuselage Fairing over the Wing (Part 5)
- 184 Fuselage Fairing over the Wing (Part 6)
- 185 Fuselage Fairing over the Wing (Part 7)
- 186 Fuselage Fairing over the Wing (Part 8)
- 187 Fuselage Fairing over the Wing (Part 9)
- 188 Fuselage Fairing over the Wing (Part 10)
- 188a Fuselage Fairing over the Wing (Part 10)
- 189 Fuselage Fairing over the Wing (Part 11)
- 190 Fuselage Fairing over the Wing (Part 12)
- 191 Cockpit Forward Coaming
- 192 Installing the Instrument Panel (revised)
- 193 Completing Cockpit Structure
- 194 Charging Receptacle Installation
- 195 Third Weight and Balance
- 196 Storing the Fuselage
- 197 Design Center of Gravity
- 198 Stab Strut Design (Part 1)
- 199 Stab Strut Design (Part 2)
- 200 Landing Gear Cross Wire
- 201 Design Center of Gravity Revision
- 202 Canopy Shape
- 203 Canopy & Windscreen Final Patterns
- 204 Two Sets of Added Fillets
- 205 Bulkhead Scalloping
- 206 Wing's Undercamber Fillets
- 207 Ballast Box if Needed
- 208 Preparing the Fuselage for Covering
- 209 Reinforcing Stab Plywood Mounting Pads
- 210 Polyspan Covering (Part 1)
- 211 Polyspan Covering (Part 2)
- 212 Polyspan Covering (Part 3)
- 213 Polyspan Covering (Part 4)
- 214 Polyspan Covering (Part 5)
- 215 Polyspan Covering (Part 6)
- 216 Red Silk Lay Out
- 217 Sectioning 1-Yard Red Silk
- 218 APC 15 X 8e Prop Gift
- 219 Silking Fin (Part 1)
- 220 Silking Fin (Part 2)
- 221 Silking Rudder
- 222 Wing Fairing, Landing Gear Cover, & Ballast Box Cover Silking
- 223 Silking Fuselage (Part 1)
- 224 Silking Fuselage (Part 2)
- 225 Silking Fuselage (Part 3)
- 226 Silking Fuselage (Part 4)
- 227 Silking Fuselage (Part 5)
- 228 Silking Fuselage (Part 6)
- 229 Silking Fuselage (Part 7)
- 230 Silking the Cowl completes the Covering
- 231 Clear Doping Red Silk
- 232 Structure through Red Silk
- 233 Lancer 850 - Fuselage and Fin Trim Designs
- 234 Lancer 850 - Color Scheme
- 235 Received 7th and 8th Orders
- 236 Covering the Elevator
- 237 Callie Graphics Decals
- 238 The Last Trim of the Day
- 239 Assembly for Trial Fitting
- 240 Wing Decal Order
- 241 Windscreen and Canopy Patterns
- 242 Received 9th Order
- 243 Covering the Stab
- 244 Alignment of Elevator Hinges and Fin Installation
- 245 Bonding of Elevator Hinges
- 246 Control surface Deflection Test
- 247 Preparing Wing for Covering (Part 1)
- 248 Preparing Wing for Covering (Part 2)
- 249 Covering the Wing (Part 1)
- 250 Covering the Wing (Part 2)
- 251 Covering the Wing (Part 3)
- 252 Covering the Wing (Part 4)
- 253 Wing Transition Striping
- 254 Wing Decals
- 255 Fourth Weight and Balance (Part 1- Weight)
- 257 Show and Tell
- 258 Request for Klass Kote Advice
- 259 Klass Kote Application Test (Part 1)
- 260 LiPo Battery Slide Modification
- 261 Received 10th Order
- 262 Building Holding Fixtures for Spray Painting
- 263 Fuselage Preparation for Spray Painting
- 264 Urethane-Satin Klass Kote Spray Test
- 265 Spraying the Lancer 850 Red Doped Silk with Klass Kote Urethane
- 266 Klass Kote's Urethane Finish Unacceptable
- 267 Preparations for Satin Klass Kote Spraying
- 268 Next Thursday for Satin Klass Kote Spraying
- 269 Spraying Satin Klass Kote
- 270 Lancer 850 - Rudder Hinging, FAA No and Lost Label
- 271 Lancer 850 - Canopy and Windscreen Installation
- 272 Lancer 850 - Final Assembly Part 1
- 273 Final Assembly (Part 2)
- 274 Final Assembly (Part 3)
- 275 Final Assembly (Part 4)
- 276 Hamilton Standard Prop
- 276 Fifth and Final Weight and Balance
- 277 Revised Performance Predictions
- 278 Project Summary
- 279 Transmitter Program Settings
- 280 Disabling ESC's BEC Function
- 281 Programming ESC and Ground Range Check
- 282 2000 mAh Battery Pack Found
- 283 Performance Predictions 2nd Revision
- 284 Project Summary Revised
- 285 Provisions for Increasing Weight Up to 80 Ounces
- 286 Maiden Flight
- 287 Second Flight Test
- 288 Lancer 850 - Postmortem of the Lancers August 2, 2019 Crash
- 289 Lancer 850 - Further Inspection of Lancer Damage
- 290-1 Lancer 850 Repair - Damage Assessment
- 291-2 Lancer 850 Repair - Development of Longeron Repair
- 292-3 Lancer 850 Repair - Several Fuselage Internal Repairs
- 294-4 Lancer 850 Repair - Reinstalling Wing Rear Attachment Block
- 295-5 Lancer 850 Repair - Rx Top Antenna Guide and Side Stringer Replacements
- 296-06 Lancer 850 Repair - Charging Jack Mounting Plate
- 297-07 Lancer 850 Repair - More Detailed Restoration Work
- 298-08 Lancer 850 Repair - Top Longeron Standoff
- 299-09 Lancer 850 Repair - Instrument Panel Replacement
- 300-10 Lancer 850 Repair - Turtle Deck Reinstalled
- 301-11 Lancer 850 Repair - Wings Undercamber Fillets
- 302-12 Lancer 850 Repair - Cockpit Forward Coaming (Part 1)
- 303-13 Lancer 850 Repair - Cockpit Forward Coaming (Part 2)
- 304-14 Lancer 850 Repair - Covering Considerations and More Detailed Work
- 305-15 Lancer 850 Repair - Installing the Instrument Panel
- 306-16 Lancer 850 Repair - Polyspan Covering (Part 1)
- 307-17 Lancer 850 Repair - Polyspan Covering (Part 2)
- 308-18 Lancer 850 Repair - Polyspan Covering
- 309-19 Lancer 850 Repair - Red Silk Covering (Part 1)
- 310-20 Lancer 850 Repair - Red Silk Covering (Part 2)
- 311-21 Lancer 850 Repair - Red Silk Covering (Part 3)
- 312-22 Lancer 850 Repair - Wing Leading Edge Repair
- 313-23 Lancer 850 Repair - Covering the Wing Leading Edge Repair
- 314-24 Lancer 850 Repair - Trimming the Fuselage Sides
- 315-25 Lancer 850 Repair - Preparing Fuselage for Spraying
- 316-26 Lancer 850 Repair - Spraying Klass Kote (Part 1)
- 317-27 Lancer 850 Repair - Spraying Klass Kote (Part 2)
- 318-28 Lancer 850 Repair - Spraying Klass Kote (Part 3)
- 319-29 Lancer 850 Repair - Reinstalling the Canopy and Windscreen
- 320-30 Lancer 850 Repair - Restoration Complete
- 321-31 Lancer 850 Repair - Cracked Trailing Edge Repair Test
- 322-32 Lancer 850 Repair - Electronic Speed Controller Installation
- 323-33 Lancer 850 Repair - Weight and Balance after Restoration
- 324-34 Lancer 850 Repair - New Speed Controller and LiPo Battery Pack
